DC-8 - AFRC

The AMPR is a total power passive microwave radiometer producing calibrated brightness temperatures (TB) at 10.7, 19.35, 37.1, and 85.5 GHz. These frequencies are sensitive to the emission and scattering of precipitation-size ice, liquid water, and water vapor. The AMPR performs a 90º cross-track data scan perpendicular to the direction of aircraft motion. It processes a linear polarization feed with full vertical polarization at -45º and full horizontal polarization at +45º, with the polarization across the scan mixed as a function of sin2, giving an equal V-H mixture at 0º (aircraft nadir). A full calibration is made every fifth scan using hot and cold blackbodies. From a typical ER-2 flight altitude of ~20 km, surface footprint sizes range from 640 m (85.5 GHz) to 2.8 km (10.7 GHz). All four channels share a common measurement grid with collocated footprint centers, resulting in over-sampling of the low frequency channels with respect to 85.5 GHz.

The Airborne Multichannel Microwave Radiometer (AMMR) measures thermal microwave emission (in degrees Kelvin of brightness temperature) from surface and atmosphere. The up-looking radiometer at 21 and 37 GHz is a component of AMMR that was developed in the 1970's for precipitation measurements from an aircraft. The entire AMMR assembly covers a frequency range of 10-92 GHz. The 21/37 GHz unit has been flown in many types of aircraft during the past three decades in various field campaigns. It was refurbished during the year 2000 and is ready for flight again.

The fixed-beam Dicke radiometer has a beam width of about 6 degrees and is currently programmed with radiometric output every second. The temperature sensitivity is < 0.5 K, and the calibration accuracy is about ±4 K. The calibration is performed on the ground by viewing targets of known brightness (e.g., sky and absorber with known brightness temperature). The unit can be installed in one of the windows of the NASA P-3 aircraft so that it views at an angle of about 15º from zenith. Thus, it is necessary to spiral the aircraft gradually down to region below the freezing level in order to make measurements effectively. Ideally, the aircraft descends at the rate of about 1 km per 5 minutes. The system requires a bottle of N2 gas to keep the wave guides dry during the in-flight operation.

Isotopic CO2 measurements have been identified as an important component of NASA's Earth Science Enterprise's Carbon Cycle Initiative as part of its program in global climate change. The isotopic composition of atmospheric CO2, and especially its 13CO2/ 12CO2 ratio, is an established tool for understanding the details of the global carbon cycle, since this ratio can distinguish between oceanic and terrestrial biospheric sinks of CO2.

The Airborne Synthetic Aperture Radar (AIRSAR) was an all-weather imaging tool able to penetrate through clouds and collect data at night. The longer wavelengths could also penetrate into the forest canopy and in extremely dry areas, through thin sand cover and dry snow pack. AIRSAR was designed and built by the Jet Propulsion Laboratory (JPL) which also manages the AIRSAR project. AIRSAR served as a NASA radar technology testbed for demonstrating new radar technology and acquiring data for the development of radar processing techniques and applications. As part of NASA’s Earth Science Enterprise, AIRSAR first flew in 1988, and flew its last mission in 2004.

Aerosols (particulate matter) have a dramatic effect on radiative forcing of the climate, in some cases cooling and in other cases warming. The Fourth Assessment Report of the IPCC estimates that direct radiative forcing due to all aerosols is a cooling of -0.50 W m-2 with absorbing aerosol (black carbon) responsible for a warming of +0.22 W m-2, but the uncertainties associated with these numbers are very large. Better measurements of the optical properties of aerosols, especially absorption coefficient and asymmetry parameter, and their spatial and temporal distribution are required to reduce these uncertainties and improve the ability of models to predict climate change. Aero3X was designed to provide such measurements. It is a light weight (11 kg), compact (0.25 x 0.30 x 0.6 m), and fast (1 Hz sample rate) instrument intended for use on an Unmanned Aerial System (UAS) but suitable for flight on other aircraft and for surface measurements. Aero3X uses an off-axis cavity ring-down technique to measure extinction coefficient and a reciprocal nephelometry technique for measurement of total-, forward- and back-scatter coefficients at wavelengths of 405 nm and 675 nm. Its outstanding precision (0.1 Mm-1) and sensitivity (0.2 Mm- 1) allow the determination of absorption coefficient, single-scattering albedo, estimates of backscatter to extinction ratio and asymmetry parameter at both wavelengths, and Angstrom exponent. Together with its humidification system for measurement of the dependence of aerosol optical properties on relative humidity, these represent a complete set of the aerosol optical properties important to climate and air quality. Aero3X was designed to operate in pollution plumes where NO2 may cause interference with the measurement, therefore, a measurement of NO2 mixing ratio is also made.

The utility of millimeter-wave radars have been successfully used for cloud sensing and cloud microphysical studies. Studies of the impact of cloud feedbacks on the earth's radiation budget have underscored the importance of having a means of measuring the vertical distribution of clouds. Millimeter-wave radars can provide this information under most conditions, with high resolution, using a relatively compact system.

The Airborne Cloud Radar (ACR) for profiling cloud vertical structure was developed by the Jet Propulsion Laboratory and the University of Massachusetts in 1996. It is a W-band (95 GHz) polarimetric Doppler radar designed as a prototype airborne facility for the development of the 94 GHz Cloud Profiling Radar (CPR) for NASA CloudSat mission.

The ACR is a third-generation millimeter-wave cloud radar. While adopting the well tested techniques used by its predecessors, ACR also has a number of new features including an internal calibration loop, frequency agility, digital I and Q demodulation, digital matched filtering, and a W-band low-noise amplifier.

ACLAIM is a 2-micron lidar operating at 100 pulses per second using an 8 cm diameter expanded beam. It was developed for advanced turbulence detection with applications to supersonic inlet control, mitigation of aircraft gust response and aircrew / passenger warning for improved seatbelt utilization.

AATS-14 measures direct solar beam transmission at 14 wavelengths between 354 and 2139 nm in narrow channels with bandwidths between 2 and 5.6 nm for the wavelengths less than 1640 nm and 17.3 nm for the 2139 nm channel. The transmission measurements at all channels except 940 nm are used to retrieve spectra of aerosol optical depth (AOD). In addition, the transmission at 940 nm and surrounding channels is used to derive columnar water vapor (CWV) [Livingston et al., 2008]. Methods for AATS-14 data reduction, calibration, and error analysis have been described extensively, for example, by Russell et al. [2007] and Shinozuka et al. [2011]. AATS-14 measurements of spectral AOD and CWV obtained during aircraft vertical profiles can be differentiated to determine corresponding vertical profiles of spectral aerosol extinction and water vapor density. Such measurements have been used extensively in the characterization of the horizontal and vertical distribution of aerosol optical properties and in the validation of satellite aerosol sensors. For example, in the Aerosol Characterization Experiment-Asia (ACE-Asia), AATS measurements were used for closure (consistency) studies with in situ aerosol samplers aboard the NCAR C-130 and the CIRPAS Twin-Otter aircraft, and with ground-based lidar systems. In ACE-Asia, CLAMS (Chesapeake Lighthouse & Aircraft Measurements for Satellites, 2001), the Extended-MODIS-λ Validation Experiment (EVE), INTEX-A, INTEX-B, and ARCTAS, AATS results have been used in the validation of satellite sensors aboard various EOS platforms, providing important aerosol information used in the improvement of retrieval algorithms for the MISR and MODIS sensors among others.

The 2D-S Stereo Probe is an optical imaging instrument that obtains stereo cloud particle images and concentrations using linear array shadowing. Two diode laser beams cross at right angles and illuminate two linear 128-photodiode arrays. The lasers are single-mode, temperature-stabilized, fiber-coupled diode lasers operating at 45 mW. The optical paths are arbitrarily labeled the “vertical” and “horizontal” probe channels, but the verticality of each channel actually depends on how the probe is oriented on an aircraft. The imaging optical system is based on a Keplerian telescope design having a (theoretical) primary system magnification of 5X, which results in a theoretical effective size of (42.5 µm + 15 µm)/5 = 11.5 µm. However, actual lenses and arrays have tolerances, so it is preferable to measure the actual effective pixel size by dropping several thousands of glass beads with known diameters through the object plane of the optics system.